Name: Jordan Truss
Address: 1135 Long Road, DeFuniak Springs, FL, 32433
Telephone: (850) 685-6410

Please complete all fields below. Enter NA, if Not Applicable. If you have any questions, please call Jordan Truss at (850) 685-6410

Customer Information Section:

Owner Name *

Builder / Distributor Name *

Contact Phone *

Email Address *

Building Address (if no address assigned, enter Parcel ID number) *

Street Address

*

City, State and Zip Code

Shipping Address for Drawings VIA UPS (NO P.O. Boxes) *

Street Address

*

City, State and Zip Code

Size of Building:

Width of gable truss to outside of post *

Pitch of gable truss *

Eaves on gable truss *

Yes

No

Chord size for gable truss *

Overhang on gable ends *

(this will be the extension of the purlins at the gable ends)

Post Size * Post Size

(final post size determined by engineer)

Length of building *

(10' spacing for enclosed buildings, 12' max for open roof only buildings)

Eave Height of gable building *

Length of lean to truss to outside of post at low end of lean to *

(NA, if not used)

Eaves on lean to *

Yes

No

Chord size for lean to *

Overhang on lean to truss ends of building *

(this will be the extension of the purlins at end of building)

Post size for lean to *

Length of lean to building *

(NA if not used)

Lean To on 1 side of building or 2 *

(enter 1, 2 or NA if not used)

Pitch of lean to *

(NA if not used)

Eave height of lean to at low end *

(NA if not used)

Open or Enclosed building? *

Open

Enclosed

(if enclosed, attach a sketch file below showing door & window sizes and locations)

PDF files preferred or scanned copies. No phone pictures of sketches.

Attach sketch if Enclosed (see note above)

Maximum file size: 134.22MB

Upload up to 2 files

Will the building have a concrete slab in Main Building? *

Yes

No

Will the building have a concrete slab in Lean To Portion? *

Yes

No

Gage of Roof Metal *

Product Approval Number for Metal Roof Panels *

Place number here and upload a PDF file of the actual Product Approval Document (obtained from your metal panel supplier). The Document gage must match the gage you input in the previous line.

Plywood deck under roof panels? *

Yes

No

Gage of Metal Siding *

NAVD flood zone elevation of building, if applicable *

(NA if not applicable; this info can be obtained from your local building authority)

If in a flood zone, enclosed building will have: *

blow out vents

finish floor elevation will typically be shown 1 foot above NAVD elevation for the building site

NA

Select Desired Engineering Drawings *

Digital Only - $567

Hard Copy Only - $567

Digital & Hard Copy - $621

Note: Commercial / Industrial engineering fees determined after review of this form.

Notes / Message

Disclaimer:
The full amount will be charged for the following but not limited to:

Revisions / changes due to incorrect information given to Jordan Truss or information not received by Jordan Truss.
Adding to a building that drawings have been completed for previously.
Drawings not submitted for permitting to the local building authority before a new version of the applicable building code is adopted by the local building authority.

Engineering is not sold without the purchase of the required trusses. After receipt of the paid engineering request form, we will calculate the correct trusses for the project and send an invoice for the trusses.

By clicking Submit you are agreeing to pay for the trusses when you receive the truss invoice. It is best for you to contact the building department and insure you can build your desired building size / type at the requested location. Refunds will not be issued for engineering fees.

Note: After submitting form, you'll be redirected to pay for drawings using Paypal or Credit Card.

Engineering Request Form

Customer Information Section:

Size of Building:

Site Map